- Buttons are sticky
- Controller has a mind of its own
- Rogue Joystick
- GameCube does not recognize controller
- Won't rumble
Dolphin simply won't detect it. I am replacing the proper drive with the WINusb drive, the driver is said to have successfully installed, yet Dolphin will not pick it up. Does anyone have any idea what the issue may be?
When you press on a button, it takes longer than usual for it to pop back up.
Before taking apart your controller, make sure that there isn't any residue that may cause the button to stick to the controller. If this is the case, simply use a pin or toothpick to scrape away at the residue. This should eliminate most of the residue. Next, use a solvent such as rubbing alcohol on a cotton swab to wipe away the rest of the 'gunk'.
There's a possibility that the rubber backing responsible for making the buttons spring back up is damaged. Prepare your screw driver! You're going to have to replace it.
Even though a button or joystick is not pressed, the console continues to register input, possibly causing a character to move uncontrollably or attack repeatedly
Sometimes dirt can activate buttons without user input. If this is the case, you may or may not have to open up the controller, depending on the amount of dirt. Before getting your hands dirty and taking apart the entire controller, wipe around the button with rubbing alcohol and cotton swabs in a circular motion. If the problem persists, go ahead and take it apart to clean it.
If it seems as though your character won't stop running around or your screen keeps going around in circles, your joystick might be set in a non-neutral position. The issue may be that you moved the the joystick before starting the game. In certain situations, this can cause a communication error between the game and the controller, causing it to malfunction. A simple fix is to not touch the joystick until the game has started.
Your console may have run into an error while booting. Errors frequently occur when the console isn't properly started. First, turn off and unplug your console, then wait about 30 seconds. This ensures all the memory from your previous gaming session has been cleared. After sufficient time as passed, go ahead and turn your console back on.
The joystick stays tilted even after you take your thumb off of it
This is a mechanical problem. Unfortunately that means you have to do some dirty work. Start by removing the joystick. Then give it a deep cleaning with rubbing alcohol.
The Joystick is not correctly attached to the motherboard
Don't worry, this isn't as scary as it sounds. Try repairing the joystick.
GameCube does not recognize controller
When you turn the GameCube on, it says 'No Controller'
Sometimes, the console may not recognize a controller if it runs into an error while booting. Errors frequently occur when the console isn't properly started. First, turn off and unplug your console from the wall, then wait about 30 seconds. This ensures all the memory from your previous gaming session has been cleared. After sufficient time as passed, turn your console back on.
Bad connector or cable
Dolphin Gamecube Controller Driver Not Detected
The first thing you will want to do is try plugging a different, working controller into the same port. If the problem persists, you may have a bad port. In that case, please refer to the GameCube device page to find a solution. Next, try plugging the original controller with the problem into a different port. If problems persist, it may be a problem with the cable or connector. If you think the issue is a bad cable, don't fear! A bad cable is better than a bad port! Make sure your cable is not twisted up or knotted. The easiest and often most successful fix to a cable not being recognized is to simply blow air into the end of the cable. These cables can dusty very easily and oxidation on electrical leads can cause controller recognition problems.
The controller won't rumble even when it should
The game does not support rumble
Some games simply do not support the rumble function. Check the instruction manual provided with the game to see if haptic feedback is supported.
Check Contact Of The port
Gamecube Controller Driver For Pc
The port contact where the controller goes may be dirty and need cleaning to make contact fully. Rumble should work after that if no other controller works with rumble in the same slot.
Unfortunately, motors sometimes fail. A motor can be fried from over use and no longer functional. At this point, the best you can do is to replace the motor.
Back to Device Page